Skip to main content
Skip table of contents

Pre-provisioned: Verify Install and Log in to UI

Verify Kommander Install and Log in to the Dashboard UI

After you build the Konvoy cluster and you install Kommander, verify your installation. After the CLI successfully installs the components, it waits for all applications to be ready by default.

NOTE: If the Kommander installation fails or you wish to reconfigure applications, you can rerun the install command to retry the installation.

If you prefer the CLI to not wait for all applications to become ready, you can set the --wait=false flag.

If you choose not to wait via the DKP CLI, you can check the status of the installation using the following command:

CODE
kubectl -n kommander wait --for condition=Ready helmreleases --all --timeout 15m

This will wait for each of the helm charts to reach their Ready condition, eventually resulting in an output resembling below:

CODE
helmrelease.helm.toolkit.fluxcd.io/centralized-grafana condition met
helmrelease.helm.toolkit.fluxcd.io/dex condition met
helmrelease.helm.toolkit.fluxcd.io/dex-k8s-authenticator condition met
helmrelease.helm.toolkit.fluxcd.io/fluent-bit condition met
helmrelease.helm.toolkit.fluxcd.io/gitea condition met
helmrelease.helm.toolkit.fluxcd.io/grafana-logging condition met
helmrelease.helm.toolkit.fluxcd.io/grafana-loki condition met
helmrelease.helm.toolkit.fluxcd.io/karma condition met
helmrelease.helm.toolkit.fluxcd.io/kommander condition met
helmrelease.helm.toolkit.fluxcd.io/kommander-appmanagement condition met
helmrelease.helm.toolkit.fluxcd.io/kube-prometheus-stack condition met
helmrelease.helm.toolkit.fluxcd.io/kubecost condition met
helmrelease.helm.toolkit.fluxcd.io/kubecost-thanos-traefik condition met
helmrelease.helm.toolkit.fluxcd.io/kubefed condition met
helmrelease.helm.toolkit.fluxcd.io/kubernetes-dashboard condition met
helmrelease.helm.toolkit.fluxcd.io/kubetunnel condition met
helmrelease.helm.toolkit.fluxcd.io/logging-operator condition met
helmrelease.helm.toolkit.fluxcd.io/logging-operator-logging condition met
helmrelease.helm.toolkit.fluxcd.io/prometheus-adapter condition met
helmrelease.helm.toolkit.fluxcd.io/prometheus-thanos-traefik condition met
helmrelease.helm.toolkit.fluxcd.io/reloader condition met
helmrelease.helm.toolkit.fluxcd.io/rook-ceph condition met
helmrelease.helm.toolkit.fluxcd.io/rook-ceph-cluster condition met
helmrelease.helm.toolkit.fluxcd.io/thanos condition met
helmrelease.helm.toolkit.fluxcd.io/traefik condition met
helmrelease.helm.toolkit.fluxcd.io/traefik-forward-auth-mgmt condition met
helmrelease.helm.toolkit.fluxcd.io/velero condition met

Failed HelmReleases

If an application fails to deploy, check the status of a HelmRelease with:

CODE
kubectl -n kommander get helmrelease <HELMRELEASE_NAME>

If you find any HelmReleases in a “broken” release state, such as “exhausted” or “another rollback/release in progress”, trigger a reconciliation of the HelmRelease using the following commands:

CODE
kubectl -n kommander patch helmrelease <HELMRELEASE_NAME> --type='json' -p='[{"op": "replace", "path": "/spec/suspend", "value": true}]'
kubectl -n kommander patch helmrelease <HELMRELEASE_NAME> --type='json' -p='[{"op": "replace", "path": "/spec/suspend", "value": false}]'

Log in to the UI

By default, you can log in to the UI in Kommander with the credentials given using this command:

CODE
dkp open dashboard --kubeconfig=${CLUSTER_NAME}.conf

You can also retrieve your credentials at any time using the following command:

CODE
kubectl -n kommander get secret dkp-credentials -o go-template='Username: {{.data.username|base64decode}}{{ "\n"}}Password: {{.data.password|base64decode}}{{ "\n"}}'

You can also retrieve the URL used for accessing the UI using the following command:

CODE
kubectl -n kommander get svc kommander-traefik -o go-template='https://{{with index .status.loadBalancer.ingress 0}}{{or .hostname .ip}}{{end}}/dkp/kommander/dashboard{{ "\n"}}'

You should only use these static credentials to access the UI for configuring an external identity provider. Treat them as back up credentials rather than use them for normal access.

You rotate the password using the following command:

CODE
dkp experimental rotate dashboard-password

The output displays the new password:

CODE
Password: kqZ31lMBSCLcBjUKVwLJMQL2PxalipIzZw5Pjyw09wDqjWV3dz2wPSSBYi09JGJp

You can perform the following operations on Identity Providers:

  • Create an Identity Provider

  • Temporarily Disable an Identity Provider

  • Create Groups

Dashboard UI Functions

After installing Konvoy component and building a cluster as well as successfully installing Kommander and logging into the UI, you are now ready to customize configurations using the Day 2 Cluster Operations Management section of the documentation. The majority of this customization such as attaching clusters and deploying applications will take place in the dashboard or UI of DKP. The Day 2 section allows you to manage cluster operations and their application workloads to optimize your organization’s productivity.

Next Step:

Pre-provisioned: Create Managed Clusters Using the DKP CLI

JavaScript errors detected

Please note, these errors can depend on your browser setup.

If this problem persists, please contact our support.